1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
|
<chapter id="config-sync">
<title>Setting up your synchronization system</title>
<para>
Synchronization presents you with two issues you'll need to
address.
<simplelist>
<member>
Your computer needs to recognize and access your handheld.
At this time, <application>Evolution</application> only
supports Palm-OS devices like the PalmPilot and the
Handspring Visor.
</member>
<member>
You should decide what sort of synchronization behavior you
want.
</member>
</simplelist>
</para>
<para>
If you haven't used a handheld device with your computer
before, you'll need to run the GNOME <application>Control
Center</application> and make sure that <application>Pilot
Link</application> is properly configured. Then, select the
<application>Evolution</application> <glossterm
linkend="conduit">conduits</glossterm> under the
<guilabel>Pilot Conduits</guilabel> section of the Control
Center.
</para>
<para>
Once your computer and your Palm-OS device are talking happily
to each other, you'll have to decide what exactly you want
them to do with the data they exchange. To enable a conduit, click the
<guibutton>Enable</guibutton> to enable it and click
<guibutton>Settings</guibutton>. Your options may vary
depending on the conduit, but typically they will be:
<variablelist>
<varlistentry>
<term>Disabled </term>
<listitem>
<para>
Do nothing.
</para>
</listitem>
</varlistentry>
<varlistentry>
<term>Synchronize</term>
<listitem>
<para>
Copy new data from the computer to the handheld, and
from the handheld to the computer. Remove items
that were on both systems but have been deleted on
one.
</para>
</listitem>
</varlistentry>
<varlistentry>
<term>Copy From Pilot</term>
<listitem>
<para>
If there is any new data on the the handheld device,
copy it to the computer.
</para>
</listitem>
</varlistentry>
<varlistentry>
<term>Copy To Pilot</term>
<listitem>
<para>
Copy new data from the computer to the handheld.
</para>
</listitem>
</varlistentry>
<varlistentry>
<term>Merge From Pilot</term>
<listitem>
<para>
Copy new data from the handheld to the computer, and
remove any information from the computer that has
been deleted on the handheld.
</para>
</listitem>
</varlistentry>
<varlistentry>
<term>Merge To Pilot</term>
<listitem>
<para>
Copy new data from the computer to the handheld, and
remove any information from the handheld that has
been deleted on the computer.
</para>
</listitem>
</varlistentry>
</variablelist>
</para>
<para>
Select a behavior for each conduit available. For the most
part, you'll want to stick with
<guilabel>Synchronize</guilabel>. Then, put your handheld on
its cradle and press the synchronization button.
</para>
<para>
<tip>
<title>Data Loss Prevention</title>
<para>
It's always a good idea to make a backup. To do that,
make a copy of your <systemitem>
<filename>~/evolution</filename> </systemitem> directory.
</para>
</tip>
</para>
</chapter>
|
